33 orders · Page 1 of 1
The High Court held that the conversion of heena leaves into herbal heena powder by mixing and grinding amounts to manufacture. The reasoning was that the process involved more than mere grinding and mixing; it included drying with various acids and then grinding with specific percentages of ingredients, resulting in a commercially different item with a distinct name and form, identifiable by buyers and sellers as a separate produce. This distinguished it from cases like Sacs Eagles Chicory and Mrs. Poonam Arora, where the processes were simpler (roasting and powdering). Therefore, profits derived from this activity were eligible for deduction under Section 80IB(4). However, in ITA No. 28 of 2009, while the assessee was eligible for the deduction under Section 80IB(4) based on the manufacturing aspect, the benefit was denied because the condition specified in Section 80IB(2)(iv) regarding the employment of ten or more workers was not complied with. The Court noted that the statements of employees indicated a maximum of eight workers were employed, falling short of the ten-worker requirement. Consequently, all appeals were dismissed except for ITA No. 28 of 2009, which was also disposed of in terms of the non-compliance with the worker condition.
The High Court held that the conversion of heena leaves into herbal heena powder by mixing and grinding amounts to manufacture. The reasoning was that the process involved more than mere grinding and mixing; it included drying with various acids and then grinding with specific percentages of ingredients, resulting in a commercially different item with a distinct name and form, identifiable by buyers and sellers as a separate produce. This distinguished it from cases like Sacs Eagles Chicory and Mrs. Poonam Arora, where the processes were simpler (roasting and powdering). Therefore, profits derived from this activity were eligible for deduction under Section 80IB(4). However, in ITA No. 28 of 2009, while the assessee was eligible for the deduction under Section 80IB(4) based on the manufacturing aspect, the benefit was denied because the condition specified in Section 80IB(2)(iv) regarding the employment of ten or more workers was not complied with. The Court noted that the statements of employees indicated a maximum of eight workers were employed, falling short of the ten-worker requirement. Consequently, all appeals were dismissed except for ITA No. 28 of 2009, which was also disposed of in terms of the non-compliance with the worker condition.
The High Court held that the conversion of heena leaves into herbal heena powder by mixing and grinding amounts to manufacture. The reasoning was that the process involved more than mere grinding and mixing; it included drying with various acids and then grinding with specific percentages of ingredients, resulting in a commercially different item with a distinct name and form, identifiable by buyers and sellers as a separate produce. This distinguished it from cases like Sacs Eagles Chicory and Mrs. Poonam Arora, where the processes were simpler (roasting and powdering). Therefore, profits derived from this activity were eligible for deduction under Section 80IB(4). However, in ITA No. 28 of 2009, while the assessee was eligible for the deduction under Section 80IB(4) based on the manufacturing aspect, the benefit was denied because the condition specified in Section 80IB(2)(iv) regarding the employment of ten or more workers was not complied with. The Court noted that the statements of employees indicated a maximum of eight workers were employed, falling short of the ten-worker requirement. Consequently, all appeals were dismissed except for ITA No. 28 of 2009, which was also disposed of in terms of the non-compliance with the worker condition.
The High Court held that the conversion of heena leaves into herbal heena powder by mixing and grinding amounts to manufacture. The reasoning was that the process involved more than mere grinding and mixing; it included drying with various acids and then grinding with specific percentages of ingredients, resulting in a commercially different item with a distinct name and form, identifiable by buyers and sellers as a separate produce. This distinguished it from cases like Sacs Eagles Chicory and Mrs. Poonam Arora, where the processes were simpler (roasting and powdering). Therefore, profits derived from this activity were eligible for deduction under Section 80IB(4). However, in ITA No. 28 of 2009, while the assessee was eligible for the deduction under Section 80IB(4) based on the manufacturing aspect, the benefit was denied because the condition specified in Section 80IB(2)(iv) regarding the employment of ten or more workers was not complied with. The Court noted that the statements of employees indicated a maximum of eight workers were employed, falling short of the ten-worker requirement. Consequently, all appeals were dismissed except for ITA No. 28 of 2009, which was also disposed of in terms of the non-compliance with the worker condition.
The High Court held that the conversion of heena leaves into herbal heena powder by mixing and grinding amounts to manufacture. The reasoning was that the process involved more than mere grinding and mixing; it included drying with various acids and then grinding with specific percentages of ingredients, resulting in a commercially different item with a distinct name and form, identifiable by buyers and sellers as a separate produce. This distinguished it from cases like Sacs Eagles Chicory and Mrs. Poonam Arora, where the processes were simpler (roasting and powdering). Therefore, profits derived from this activity were eligible for deduction under Section 80IB(4). However, in ITA No. 28 of 2009, while the assessee was eligible for the deduction under Section 80IB(4) based on the manufacturing aspect, the benefit was denied because the condition specified in Section 80IB(2)(iv) regarding the employment of ten or more workers was not complied with. The Court noted that the statements of employees indicated a maximum of eight workers were employed, falling short of the ten-worker requirement. Consequently, all appeals were dismissed except for ITA No. 28 of 2009, which was also disposed of in terms of the non-compliance with the worker condition.
The High Court held that the conversion of heena leaves into herbal heena powder by mixing and grinding amounts to manufacture. The reasoning was that the process involved more than mere grinding and mixing; it included drying with various acids and then grinding with specific percentages of ingredients, resulting in a commercially different item with a distinct name and form, identifiable by buyers and sellers as a separate produce. This distinguished it from cases like Sacs Eagles Chicory and Mrs. Poonam Arora, where the processes were simpler (roasting and powdering). Therefore, profits derived from this activity were eligible for deduction under Section 80IB(4). However, in ITA No. 28 of 2009, while the assessee was eligible for the deduction under Section 80IB(4) based on the manufacturing aspect, the benefit was denied because the condition specified in Section 80IB(2)(iv) regarding the employment of ten or more workers was not complied with. The Court noted that the statements of employees indicated a maximum of eight workers were employed, falling short of the ten-worker requirement. Consequently, all appeals were dismissed except for ITA No. 28 of 2009, which was also disposed of in terms of the non-compliance with the worker condition.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, resulting in a complete transformation into a new and different article with a distinct identity, characteristic, and use. The Court concluded that the ITAT was justified in holding that the paper-insulated wires and strips were commercially different from the raw material and were commercially known as such, entitling the assessees to deductions under Section 80 IC. Therefore, Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court distinguished the facts of the present case from the Supreme Court's decision in Collector of Central Excise vs. Technoweld Industries Ltd. The Court noted that in Technoweld, the process was primarily wire drawing to a thinner gauge without significant changes in chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes involved substantial transformations. Consequently, Question No. 2 was also answered against the revenue. The appeals filed by the revenue were dismissed.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, resulting in a complete transformation into a new and different article with a distinct identity, characteristic, and use. The Court concluded that the ITAT was justified in holding that the paper-insulated wires and strips were commercially different from the raw material and were commercially known as such, entitling the assessees to deductions under Section 80 IC. Therefore, Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court distinguished the facts of the present case from the Supreme Court's decision in Collector of Central Excise vs. Technoweld Industries Ltd. The Court noted that in Technoweld, the process was primarily wire drawing to a thinner gauge without significant changes in chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes involved substantial transformations. Consequently, Question No. 2 was also answered against the revenue. The appeals filed by the revenue were dismissed.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, resulting in a complete transformation into a new and different article with a distinct identity, characteristic, and use. The Court concluded that the ITAT was justified in holding that the paper-insulated wires and strips were commercially different from the raw material and were commercially known as such, entitling the assessees to deductions under Section 80 IC. Therefore, Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court distinguished the facts of the present case from the Supreme Court's decision in Collector of Central Excise vs. Technoweld Industries Ltd. The Court noted that in Technoweld, the process was primarily wire drawing to a thinner gauge without significant changes in chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes involved substantial transformations. Consequently, Question No. 2 was also answered against the revenue. The appeals filed by the revenue were dismissed.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, resulting in a complete transformation into a new and different article with a distinct identity, characteristic, and use. The Court concluded that the ITAT was justified in holding that the paper-insulated wires and strips were commercially different from the raw material and were commercially known as such, entitling the assessees to deductions under Section 80 IC. Therefore, Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court distinguished the facts of the present case from the Supreme Court's decision in Collector of Central Excise vs. Technoweld Industries Ltd. The Court noted that in Technoweld, the process was primarily wire drawing to a thinner gauge without significant changes in chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes involved substantial transformations. Consequently, Question No. 2 was also answered against the revenue. The appeals filed by the revenue were dismissed.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, resulting in a complete transformation into a new and different article with a distinct identity, characteristic, and use. The Court concluded that the ITAT was justified in holding that the paper-insulated wires and strips were commercially different from the raw material and were commercially known as such, entitling the assessees to deductions under Section 80 IC. Therefore, Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court distinguished the facts of the present case from the Supreme Court's decision in Collector of Central Excise vs. Technoweld Industries Ltd. The Court noted that in Technoweld, the process was primarily wire drawing to a thinner gauge without significant changes in chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes involved substantial transformations. Consequently, Question No. 2 was also answered against the revenue. The appeals filed by the revenue were dismissed.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court noted that the revenue did not dispute the assessees' entitlement to deductions under Section 80 IC, only the characterization of their activity. The assessees argued that drawing wire from wire rods constituted manufacture. The ITAT had found that the process involved reducing wire rods to smaller sizes, facilitating drawing at high speeds, and subsequent annealing to overcome stresses and embrittlement. The High Court found that qualitative changes like annealing, quenching, acid pickling, flux application, and galvanizing, following the zinc hot dip, definitely amounted to manufacture, resulting in a complete transformation of raw materials into a new and different article with a different identity, characteristic, and use. Therefore, the assessees were engaged in the manufacture of a product commercially different from its raw material and were eligible for deductions under Section 80 IC. Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court analyzed the Supreme Court's judgment in Technoweld Industries and concluded that the facts in that case were totally different. In Technoweld, the process was merely drawing wire into a thinner gauge without changing chemical, electrical, or mechanical properties, and no new product emerged. The High Court reiterated its finding that the assessees' processes amounted to manufacture or production, making them eligible for Section 80 IC deductions, and thus, Question No. 2 was also answered against the revenue. The appeals were dismissed.
The High Court held that the process undertaken by the assessees amounted to manufacture or production. Regarding Question No. 1, the Court noted that the revenue did not dispute the assessees' entitlement to deductions under Section 80 IC, only the characterization of their activity. The assessees argued that drawing wire from wire rods constituted manufacture. The ITAT had found that the process involved reducing wire rods to smaller sizes, facilitating drawing at high speeds, and subsequent annealing to overcome stresses and embrittlement. The High Court found that qualitative changes like annealing, quenching, acid pickling, flux application, and galvanizing, following the zinc hot dip, definitely amounted to manufacture, resulting in a complete transformation of raw materials into a new and different article with a different identity, characteristic, and use. Therefore, the assessees were engaged in the manufacture of a product commercially different from its raw material and were eligible for deductions under Section 80 IC. Question No. 1 was answered against the revenue. Regarding Question No. 2, the Court analyzed the Supreme Court's judgment in Technoweld Industries and concluded that the facts in that case were totally different. In Technoweld, the process was merely drawing wire into a thinner gauge without changing chemical, electrical, or mechanical properties, and no new product emerged. The High Court reiterated its finding that the assessees' processes amounted to manufacture or production, making them eligible for Section 80 IC deductions, and thus, Question No. 2 was also answered against the revenue. The appeals were dismissed.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the process undertaken by the assessees amounts to manufacture or production. The court found that qualitative changes were effected in the raw material through processes like annealing, quenching, acid pickling, flux application, and galvanizing, leading to a complete transformation into a new and different article with a distinct identity, characteristic, and use. This transformation resulted in a commercially different commodity, no longer regarded as the original raw material but as a new and distinct article. Therefore, the assessees were engaged in the manufacture of a product and were eligible for deductions under Section 80 IC. Regarding the reliance on the Technoweld Industries case, the court distinguished the facts, stating that in Technoweld, the process was merely drawing wire into a thinner gauge without imparting different chemical, electrical, or mechanical properties, and no new product was manufactured. In contrast, the present assessees' processes resulted in a commercially different product. Consequently, the question regarding the Technoweld judgment was answered against the revenue. The appeals were dismissed, and the assessees were held eligible for the deductions claimed under Section 80 IC.
The High Court held that the ITAT had correctly interpreted the provisions of Section 115JB of the Act and applied them to the facts of each case. The Court affirmed the findings recorded by the ITAT. Regarding the invocation of Section 263, the Court reiterated the principles laid down by the Supreme Court in cases like Malabar Industrial Co. Ltd., Max India Limited, and Greenworld Corporation Parwanoo. It was held that the conditions for exercising jurisdiction under Section 263, namely that the order must be erroneous and prejudicial to the interest of the revenue, are conjunctive. Every loss of revenue does not automatically mean prejudice to the revenue, especially when the AO has taken a view permissible in law or where two views are possible and the AO has taken one view that is not unsustainable in law. The ITAT's conclusion that the CIT was not justified in invoking Section 263, due to lack of material to establish that the AO's order was erroneous and prejudicial to the revenue, was upheld. The substantial questions of law raised in all the appeals were answered in line with the ITAT's findings. Consequently, all appeals filed by the Commissioner of Income Tax were dismissed.
The High Court held that the ITAT had correctly interpreted the provisions of Section 115JB of the Act and applied them to the facts of each case. The Court affirmed the findings recorded by the ITAT. Regarding the invocation of Section 263, the Court reiterated the principles laid down by the Supreme Court in cases like Malabar Industrial Co. Ltd., Max India Limited, and Greenworld Corporation Parwanoo. It was held that the conditions for exercising jurisdiction under Section 263, namely that the order must be erroneous and prejudicial to the interest of the revenue, are conjunctive. Every loss of revenue does not automatically mean prejudice to the revenue, especially when the AO has taken a view permissible in law or where two views are possible and the AO has taken one view that is not unsustainable in law. The ITAT's conclusion that the CIT was not justified in invoking Section 263, due to lack of material to establish that the AO's order was erroneous and prejudicial to the revenue, was upheld. The substantial questions of law raised in all the appeals were answered in line with the ITAT's findings. Consequently, all appeals filed by the Commissioner of Income Tax were dismissed.
The High Court held that the ITAT had correctly interpreted the provisions of Section 115JB of the Act and applied them to the facts of each case. The Court affirmed the findings recorded by the ITAT. Regarding the invocation of Section 263, the Court reiterated the principles laid down by the Supreme Court in cases like Malabar Industrial Co. Ltd., Max India Limited, and Greenworld Corporation Parwanoo. It was held that the conditions for exercising jurisdiction under Section 263, namely that the order must be erroneous and prejudicial to the interest of the revenue, are conjunctive. Every loss of revenue does not automatically mean prejudice to the revenue, especially when the AO has taken a view permissible in law or where two views are possible and the AO has taken one view that is not unsustainable in law. The ITAT's conclusion that the CIT was not justified in invoking Section 263, due to lack of material to establish that the AO's order was erroneous and prejudicial to the revenue, was upheld. The substantial questions of law raised in all the appeals were answered in line with the ITAT's findings. Consequently, all appeals filed by the Commissioner of Income Tax were dismissed.
The High Court held that the ITAT correctly interpreted the provisions of Section 115JB of the Act and applied them to the facts of each case. The Court affirmed the findings of the ITAT. The reasoning implies that the ITAT's decision to allow the deduction from book profits was upheld. Regarding Section 263, the Court's affirmation of the ITAT's findings suggests that the ITAT found the CIT's invocation of Section 263 to be unjustified, likely because the AO's order was not considered erroneous or prejudicial to the revenue. The ratio decidendi is that the ITAT's interpretation and application of Section 115JB and the principles governing Section 263 were correct. The appeals were dismissed, affirming the ITAT's orders.